Msi 7222 manual

Connect the equipment into an outlet on a circuit different from that to which the receiver is. The changes or modifications not expressly approved by the party responsible for compliance could void. Shielded interface cables and A. Operation is subject to the following two conditions:. Previous Page.

Next Page. Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation Micro-Star International MS GX We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents.

Our products are under continual improvement and we reserve the right to make changes without notice. Page 3: Safety Instructions Safety Instructions 1. Always read the safety instructions carefully.

Keep this User Manual for future reference. Keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. The openings on the enclosure are for air convection hence protects the equipment from overheating.

Do not cover the openings. You can return these products to local collection points. Page 6 Table of Content English Overheating Overheating will seriously damage the CPU and the system. Always make sure the cooling fan can work properly to protect the CPU from overheating. If you do not have the cooler, contact your dealer to purchase and install them before turning on the computer.

Make sure your CPU cooler is firmly installed before turning on your system. Do not touch the CPU socket pins to avoid damage. Page 14 IDE1. IDE1 can connect a Master and a Slave drive. You must configure second hard drive to Slave mode by setting the jumper accordingly.

MSI Reminds You If you install two hard disks on one cable, you must configure the second drive to Slave mode by setting its jumper. Always consult the vendors for the proper CPU cooling fan. You can clear CMOS by shorting pin while the system is off. Then return to pin position. Page 19 Integrated Peripherals Use this menu to specify your settings for integrated peripherals. Power Management Setup Use this menu to specify your settings for power management. Page Usb Connectors Tape player, or other audio devices.

Mic is a connector for microphones. Pin Definition Always consult the vendors for proper CPU cooling fan.

Please refer to the recommended CPU fans at Intel official website. Please do not fold the serial ATA cable in a degree angle, since this might cause the loss of data during the transmission. USB 2. AGP is an interface specification designed for the throughput demands of 3D graphics. It introduces a 66MHz, bit channel for the graphics controller to directly access main memory.

Page Chapter 3. The items under each BIOS category described in this chapter are under continuous update for better system performance. Date mm:dd:yy This allows you to set the system to the date that you want usually the current date.

Floppy A This item allows you to set the type of the floppy drives installed. Available options: [Disabled], [ KB, 5 ], [1. Setting options: [Enabled], [Disabled]. Change these settings only if you are familiar with the chipset.

Write Recovery Time Twr This function specifies the amount of delay in clock cycles that must elapse after the completion of a valid write operation, before an active bank can be precharged. The Fast Write technol- ogy allows CPU to write directly into the graphics controller without passing anything through system memory and improves 8x speed accordingly. Setting options: [Slowest], [Default], [Optimize]. Setting options: [Disabled], [Enabled]. S3-related functions described in this section are available only when your BIOS supports S3 sleep mode.

Settings: [Disabled], [1], [2], [4], [8], [10], [20], [30], [40], [50], [60]. Monitor function is available only if there is hardware monitoring mechanism onboard.

The Optimized Defaults are the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. Page Chapter 4. Introduction To Realtek Alc Chapter 2. ALC allows the board to attach 4 or 6 speakers for better surround sound effect.

Follow the procedures described below to install the drivers for different operating systems. Click Finish to restart the system. Select this option 4 - To enable 4- or 6-channel audio operation, first connect 4 or 6 speakers to the appropriate audio connectors, and then select 4- or 6-channel audio setting in the software utility. Page 67 MS Micro-ATX Mainboard Connecting the Speakers When you have set the Multi-Channel Audio Function mode properly in the soft- ware utility, connect your speakers to the correct phone jacks in accordance with the setting in software utility.

Page 68 Introduction to Realtek ALC n 4-Channel Mode for 4-Speaker Output The audio jacks on the back panel always provide 2-channel analog audio output function, however these audio jacks can be transformed to 4- or 6- channel analog audio jacks by selecting the corresponding multi-channel operation from No.

Select this function Note that this function applies only for 2-channel audio operation. Playing KaraOK 1. Click the audio icon from the window tray at the lower-right corner of the screen.

Page Chapter 5. Using 4- or 6-Channel drives. Auto Setup allows BIOS to select the disk drives and create arrays automatically, but it does not duplicate the mirroring drives even if the user selected Create and duplicate for RAID 1. Even though 64KB is the recommended setting for most users, you should choose the block size value which is best suited to your specific RAID usage model.

Power off and Check the Failed Drive: This item turns off the computer and replaces the failed hard drive with a good one. If your computer does not support APM, you must turn off your computer manually. After replacing the hard drive, boot into BIOS and select Choose replacement drive and rebuild to rebuild the broken array. The InstallShield Wizard will begin automatically for installation.

Click on the Next button to proceed the installation in the welcoming window. Then click Next button to proceed the installation. After the software is finished installation, it will automati- cally started every time Windows is initiated. There are two viewing types: By controllers and by device. Click on the object in the left window pane to display the status of the object in the right windowpane.